TV / SAT connection sockets

TV/SAT connection sockets for flush-mounted and surface-mounted installation

DINIC antenna sockets for electrical installations, building services and specialist retailers: Choose between 2-hole sockets for TV and radio and 3-hole sockets for satellite, TV and radio. Both white versions are suitable for flush-mounted and surface-mounted installation; the cover and surface-mounted frame are included in the scope of delivery.

TV and radio: 2-hole

Antenna socket with 10 dB output attenuation, without DC pass-through, for compatible TV/radio distribution systems.

SAT, TV and radio: 3-hole

SAT antenna socket with three outputs and DC pass-through for powering and switching SAT components.

The choice depends on the signal type, attenuation, DC pass-through and the socket’s position in the distribution system. The appropriate configuration is determined by the system plan.

1 to 2 (from a total of 2)

Which antenna socket is suitable for the TV/satellite system?

Whether it’s a new installation or a replacement: ensure the aerial socket is compatible with the existing distribution network. Check the signal type, connection ratings, required DC continuity and line termination. The number of sockets alone is not sufficient to guide your choice.

DINIC 2-Loch-Antennendose für TV und Radio mit Abdeckung und Aufputzrahmen

2-port antenna socket for TV and radio

  • 10 dB output attenuation; system impedance 75 ohms.
  • TV: 0.5–1000 MHz; Radio: 0.5–139 MHz.
  • No DC pass; not suitable for satellite IF distribution.
  • White, flush-mounted/surface-mounted, DINIC blister pack with Euro hole.

View the 2-hole antenna socket A-DO-2UD

DINIC 3-Loch-Antennendose für SAT, TV und Radio mit Abdeckung und Aufputzrahmen

3-hole antenna socket for satellite, TV and radio

  • Three separate outputs for satellite, TV and radio.
  • With DC pass-through for satellite components.
  • Pluggable terminating resistor included.
  • White, flush-mounted/surface-mounted, DINIC box with Euro hole.

View the 3-port SAT socket A-DOS-3U-V2-KB

Junction/termination socket or feed-through socket?

Both DINIC models are described as branch/termination sockets with a terminating resistor. According to the product specifications, they can be used as pass-through sockets by removing the terminating resistor. Select the configuration to suit the cable routing and the intended termination of the system.

When replacing a socket, the type, attenuation values and pin configuration of the existing socket should be checked against the design specifications. A cover that fits externally does not necessarily confirm electrical compatibility.

What does 10 dB mean for an aerial socket?

For the 2-hole socket, the specification ‘10 dB’ refers to the output attenuation at the device connection. It is not a measure of shielding. The required attenuation depends on the signal level and the distribution; a lower value is not automatically better. The 10 dB value applies here to the 2-hole version.

Flush-mounted and surface-mounted: installation to suit the property

Both aerial sockets are supplied with a cover and a surface-mounted frame. This means that versions are available for both flush-mounted and surface-mounted installation. If the socket is to be integrated into an existing switch range, please check the mechanical dimensions and the suitable centre plate in advance.

Suitable aerial cables and satellite connection cables

Frequently asked questions about TV/SAT connection sockets

Can I use the 2-port socket for a satellite receiver?
This 2-port version is designed for TV and radio, supports up to 1000 MHz at the TV output and has no DC pass-through. It is not intended for SAT IF. Please check the 3-port SAT version and the requirements of your system.

Is every 3-port socket suitable for a cable modem?
No. Three sockets or an F-connector alone do not guarantee suitability for cable internet. The DATA connection, frequency ranges, return path and the cable network operator’s specifications must be compatible with the modem connection.

TV/SAT connection sockets for your B2B requirements

For a specific enquiry, please let us know the signal type, existing socket type, required attenuation, mounting type and quantity. MAG supports specialist retailers, installation companies and commercial buyers with product selection.

Send a B2B enquiry to MAG